Double acting hydraulic cylind

发布时间：2009-09-20 来源：扬子工具集团 浏览次数:52766
Remarks l．Circularity here shall be expressed as the difference between the maxi-
    mum diameter and the minimum diameter at an arbitrary section of a
    tube，and the maximum value of circularity throughout the whole length of
    the tube shall not exceed the value given in this Table．
2．Cylindricity here shall be expressed as the difference between the maxi—
 mum diameter and the minimum diameter measured throughout the
 whole length of the tube．
3．Bending of the tube shall be not more than l mm per l000 mlTl．
Table l3．Finished dimensiOIlS of rods
Unit：mm

    Rod diameter
    Tolerances on
 finished dimension
 Circularity and
 cylindridty
    lO l2 14 16 18
    —0.016
    —0．O43
    0.027
 
    20 22 25 28
    ——0.020
    —0.053
    0.033
 
 32 36 40 45 50
 
    —0.025
 
    一O．064
 
    0．o39
 
 
    56 63 70 80
 
    ——0.030
 
    —0.076
 
    0.046
 
 
 90 100 110 125
 
    —0.036
 
    一O．O90
 
    0.054
 
 
 140 160 180
 
    —0．O43
 
    —0.106
 
    0.063
 

15
B 8354．1992
Remarks l．Circularity here shall be expressed as the difference between the maxi-
    mum diameter and the minimum diameter at an arbitrary sectic fl of a rod，
    and the maximum circularity throughout the whole length of the rod shall
    not exceed the value given in this Table．
2．Cylindricity here shall be expressed as the difference between th≥maxi-
 mum diameter and the minimum diameter measured throughou：the
 whole length of the rod．
3．Bending of the rod shall be not more than 0．25 mm per l000 mm
7．2—Finish of sl—iding faces The finish of the tube inside face，sliding faces of
the rod and bush shall be expressed by the center line mean roughness，and shall
be approximately the roughness of Table l 4．
Table l4．Finish of sliding faces

    Division according to sliding face
    and applicable packing
 
    Surface roughness
 
 Rubber
 0.4a(1.6S)
 Sliding face of rod to
 packing
 Fabric reinforced
 rubber
 
 0.8 a(3.2S)
 Others
 0.8 a(3.2 S)
 
 Rubber
 0.4 a(1.6 S)(3)。0.8 a(3.2 S)
S1iding face of tube
 
Fabric reinforced
 rubber
 
 0.8 a(3.2S)
 reside to paclcmg
 
 
 Metal
 
 0.4 a(1.6 S)
 Others
 0.8 a(3.2 S)
 Sliding face of pison
 0.8 a(3.2S)
 Sliding face of bush
 1.6 a(6.3 S)

 
Note(3) When 0-ring or X-ring is used．
Remarks l．Surface roughness shall be as defined in JIS B 0601．
    2．Surface roughness given in parentheses should not be used as
    far as possible．
7．3．Stroke length The stroke lengths shall be in accordance with Tat le l5，
and the tolerances thereof shall be in accordance with Table l6．
    Even if Table l 5 is not applicable，it should preferably be in accord ance with
the provisions of JIS Z 8601．
Unit：mm
7．4
Table l6．Tolerances on stroke lengths
Unit：mm

 
    Tolerances
    Stroke length
    Division
    GradeA
    GradeB
 
 i00 and under
 
    +0.8
 
    O
    +1.6
 
    0
 
 Over i00 up to and incl．250
 
    +1．O
 
    O
    +2.5
 
    O
 
 Over 250 up to and incl．630
 
    +1.25
 
    0
    +4．O
 
    0
 
 Over 630 up to and incl．i000
 
    +1.4
 
    O
    +5.0
 
    O
 
 Over l000 up to and ind．1600
    +1.6
    0
    +6.3
    O
 
 Over l600 up to and incl．2000
    +1.8
    O
    +8.0
    0

 
tube end face and fitting face of the cylinder cover
more than 0．04 mm．
The perpendicularity of the
to the shaft axis shall be not
7．5—Perpendicularity and—coaxiality of piston The perpendicularity of end face
of a piston body to its shaft axis shall be not more than 0．04 mm，and the
coaxiality of sliding face to the piston shaft axis shall be not more than 0．03 mm．    、．，，
7．6 Fits of piston and tube The fits of the sliding face of the piston and that
of the tube having been subjected to turning or honing should be of H 7／g 7 speci．
fled in JIS B 0401 for the piston using piston rin9，and be of H 9／f 8 for that
using packin9．For the tube having been subjected only to honin9，it is allowed to
use for the piston using packing SO long as it has the same clearance as the fit of
H 9／f 8 within the range of Table ll and Table l2．
7．7
and
 Fits of bush and rod The fits of the bush(or a part corresponding to it)
the rod should conform to H 9／f 8 specified in JIS B 040 1．
7．8．1 Screw threads of rod end The screw
fine threads specified in JIS B 0207，and the
diameter shall conform to Table l7(A)．
threads of rod end shall be of metric
dimensions with respect to the rod
17
B 8354．1992
    However，if Table l7(A)is not applicable，Table l7(B)should aW ly．
    The permissible dimensional deviation and tolerance shall confoFIE t0 6 9
specified in JIS B 021 1．
    When screw threads with pitches longer than those given in Table l7(A)
and Table l7(B)are used，it is recommended to select them among thos≥speci．
fied in Table l7(C)．
Table l7(A)Screw thread of rod end

 
 Rod diameter
 
 Nominal
 designation 01"
screw thread
 Length of
 screw—thread
 
 
 Rod diameter
 
    Nominal
 designation of
 screw thread
    I
 8Cr
 
    10(11.2)
M 8×1
    12
    50
 M 45×1.5
 
    12(12.5)
M 10 X 1.25
    15
    56
 M 48 X 1.5
 
    14
 M 12 X 1.25
    18
    63
 M 56×2
 
    16
 M 14 X 1.5
    20
    70(71)
 M 64 X 2
 
    18
 M 16 X 1.5
    25
    80
 M 72×2
 
    20
 M 18 X 1.5
    27
    90
 M 80×2
 
 22(22.4)
M 20 X 1.5
    30
 100
 M 95 X 2
 
 25
 M 22×1.5
    33
 110(112)
 M i00 X 2
 
    28
 M 24×1.5
    35
    125
 M 120 X 2
 
    32(31.5)
M 27×1.5
    40
    140
 M 130 X 2
 
    36(35.5)
M 30×1.5
    45
    160
 M 150 X 2
 
 40
 M 33×1.5
    50
    180
 M 170 X 2
 
 45
 M 39×1.5
    60
 

 
Table l7(B)Screw thread of rod end

 
 Rod diameter
 
 Nominal
 designation ot
 screw thread
 Length of
 screw thread
 
 
 Rod diameter
 
    Nominal
 designation of
 screw thread
    L
 Scr
 
    10(11.2)
M 8 X 1
    12
    50
 M 39×1.5
 
 12(12.5)
M 8 X 1
    12
    56
 M 42 X 1.5
 
    14
 M 10 X 1.25
    15
    63
 M 48 X 1.5
 
    16
 M 12 X 1.25
    18
    70(71)
 M 56×2
 
    18
 M 14 X 1.5
    20
    80
 M 60 X 2
 
    20
 M 16 X 1.5
    25
    90
 M 68 X 2
 
 22(22.4)
M 18 X 1.5
    27
 100
 M 76 X 2
 
    25
 M 20 X 1.5
    30
 110(112)
 M 85 X 2
 
    28
 M 22 X 1.5
    33
    125
 M 90×2
 
 32(31.5)
M 24 X 1.5
    35
    140
 M 100 X 2
 
 36(35.5)
M 27 X 1.5
    40
    160
 M 120 X 2
 
    40
 M 30×1.6
    45
    180
 M 130 X 2
 
    45
 M 33×1.5
    50
 

18
B 8354．1992
 Table l7(C)Screw thread of rod end
Unit：mm

 Nominal desig-
natlon oi screw
    thread
 Nominal desig-
na钮on oI screW
    thread
 M 3×0.35
 M 4×0.5
 M 5×0.5
 M 6×0.75
 M 8×1
 M 10×1.25
 M 12×1.25
 M 14×1.5
 M 16×1.5
 M 18×．l．5
 M 20×1.5
 M 22×1.5
 M 24×2
 M 27×2
 M 30×2
 M 33×2
 M 36×2
 M 42×2
 M 48×2
 M 56×2
 M 64×3
 M 72×3
 M 80×3
 M 90×3
 M i00×3
 M 110×3
 M 125×4
 M 140×4
 M 160×4
 M 180×4
 M 200×4
 M 220×4
 M 250×6
 M 280 x 6

 
Informative reference：The nominal designations of screw threads conform
    to those specified in IS0 4395：1978
7．8．．2—Pin holes a—t rod ends The dimensions of the pin holes at rod ends shall
conform to Table l8．

 

本文链接: http://www.yzgj.cn/yzgjcn_172.html
如需转载请注明:扬子工具液压千斤顶http://www.yzgj.cn

本文章总10页 上一页 1 2 3 4 5 6 7 8 9 10 下一页

上一篇:伸缩式套筒液压缸
下一编:液压接头和插头尺寸规范
千斤顶相关知识
■液体静力学
■液压传动基础知识
■液压动力元件
■液压千斤顶原理、发明、简介、工作原理图
■液压传动的优缺点
■液压缸掌握原始资料和设计依据
液压千斤顶相关产品(请点击产品名称查看详细资料)
电动液压千斤顶(海力F-V50-1000T) - 同步千斤顶 - 大吨位液压顶(海力F-Q顶管机大行程) 大吨位分离式液
压顶
薄型顶(吨位5-200T行程6-80mm) - 薄型同步千斤顶(薄型海力B-V)
桥梁千斤顶(海力M-B) - 超薄型千斤顶(RSM5-150T) - 薄型千斤顶(RCS5-100T) 		空间窄小-如桥梁
更换支座
穿心千斤顶(海力H-C空心顶) - 空心千斤顶(RCH穿心顶) - 双作用空心千斤顶(RRH) 具有拉伸功能空
心液压顶
自锁千斤顶(海力L-V50-1080T) - 自锁同步千斤顶 - 自锁式千斤顶(CLL) 需长时间支撑重
物液压顶
分离式千斤顶(10-200T) - 手动千斤顶(5-100T) - 双节千斤顶(多节) 小吨位分离式液
压顶
超高压千斤顶(CLR) - 电动千斤顶(DYG) - 大吨位千斤顶(CLS) 大吨位液压顶旧
型号
电动泵(海力B-V电动泵站) - 手动泵(YSB单向) - 双向手动泵(YSSB) - 单向手动泵(YCSB)
液压千斤顶选型调查表(在括号中填上数据，并留下联系方法，最后再提交)
单位:
姓名:
电话:
传真:
手机:
邮箱: