Double acting hydraulic cylind

发布时间:2009-09-20 来源:扬子工具集团 浏览次数:60558

This Japanese Industrial Standard specifies the double acting hydraulic cylinders,hereafter referred to as the”cylinders”,to be used in the hydre-ulic systems(2)for mechanical equipment(1).2.JIS Notes(1)Those which are used in production such as manufacturir g and  assemblin9.

(2)Those which are prescribed in JIS B 8361.
Remarks l.
2.
Definitions
B 0142 apply,
The units and numerical values given in()in this E tands,rd
are based on the traditional units and are appended for
informative reference.
The standards cited in this Standard are shown in/.ttached
Table 2,and corre8ponding International Standards are
shown in Attached Table 3.
For the main terms used in this Standard,the defini;ions in
and the rest of the terms shall be as follows:
Informative reference:The definitions for terms are given in IS0 5 598.
(1) maximum permissible working pressure The maximum value pe】missible
    for pressure generated inside the cylinder.
Remarks:This means such pressures as internal pressure,which.results
    from the absorption of energy when inertial loads are.topped,
    and surge pressure.which is generated when the direc:ion of oil
    flow is changed.
(2)—nominal—pressure The pressure assigned for the purpose of cony(nient
    designation,and the maximum value of the set pressures for reliev ng valves
    provided in an oil hydraulic circuit using cylinders.
minimum operating pressure.The minimum pressure capable of,,uaran-
teeing the opera,on of the cylinder.
(4)—head—end Closed end of the cylinder.
(5)—rod—end End of a cylinder through which the piston rod passes.
    Informative reference:
Head end    Rod end


 

2
B 8354.1992
where,
A theoretical fluid force acting on the surface of a piston.
    E^=0.1×P X A
    慨JI=P X A)
    EJl: cylinder force(kN){kgfl
P: nominal pressure acting on the surface of
    the piston(MPa){kgf/cm2)
A: effective cross-sectional area of the piston
    (cm2)
A mechanical force transmitted by a piston rod.
(8)—thrust efficien—cy of cylinder The ratio of the cylinder output force to the
    cylinder force.
where,
thrust efficiency of cylinder
cylinder output force(kN){kgf}
nominal working pressure acting on the
surface of a piston(MPa){kgf/cm2)
A: effective cross·sectional area of the piston
    (cm2)    .
c...y.....1..i...n.....d.....e....r......c....u.....s...h.....i...o....n.....i...n...—9— Means whereby the movement of a rod is decelerated
as it approaches the end of its stroke by restricting the discharge of fluid
automatically.
3一—Surrou—ndings The cylinders shall be used in indoor surroundings and
shall not be used in the surroundings of excessive vibration,contamination,and
high humidity.
3.2 Ambient temperature The ambient temperature shall be一5。C t0 80。C.
3.3 Working fluid The working fluid used shall be mineral working oil.
The piston speeds shall be as given in Table l.
Table l.Piston speeds

    Tube bores IIIIIl
    Piston speed mm/s
    32    40    50    63
    8 t0 400
    80    100 125
    8t0300
    140    160 180
    200    220 250
    8t0200
 

 
shall be not more than the values shown in Figs.1,2 and 3.
B 8354.1992
3.6 Maximum permissible working pressures The maximum permissible
working pressures for cylinders shall be classified as given in Table 2.
Table 2.Maximum permissible working pressures
Unit:MPa{kgf/cm2)

 
 
    Rod end
Nominal pressure
 
    Head end
 
 Red diameter
    symbolA
 Rod diameter
    SymbolB
 Rod diameter
 symbol C
    7(70l
    8.8{90】
    14.7{150)
    12.7{130)
    10.8{110)
    14 f140】
    17.7(180】
    17.7 f180】
    17.7 f180l
    13.7(140】
    21{210)
 26.5{270)
 26.5{270l
 24.5{250l
 

 
4.Types The types of the cylinders shall be classified as given in the
following according to nominal pressures,mounting forms,materials of packing
and gasket,cushionings,external leakages(1eakages from rod wiper portion),and
with or without switches.
(1) Nominal pressure The cylinders shall be classified as given in Table 3
    according to the nominal pressures:
Table 3.Nominal pressures of cylinder
Unit:MPa
Nominal pressure
7{70)
14(140l
21 1210l
(2) Mounting forms The cylinders shall be classified as given in Table 4
    according to the mounting forms:
Table 4.Mounting forms

 
    Mounting type
    Symbol
    Remarks
 
 Right-angled to axis foot type
 LA
 (MS 2)
 Tables l9&20
 Foot types
 
 
 Axial direction foot type
 
    LB
 
 (MS l)
 
 Table21
 
 Rod-end rectangular flange type
 FA
 (MF l)
 Tables 22,23&24
 Head-end rectangular flange type
    FB
 (MF 2)
 Tables22,23&24
 Flange types
 
 
 ROd-end square flange type
 
    FC
 
 (MF 5)
 
 Table25
 Head-end square flange type
 FD
 (M田6)
 Table25
 
 Detachable eye type
 CA
(MP4)
Table 26
 Crevice
 Detachable crevice type
 CB
 (M:P2)
 Table 26
 types
 
 
 Fixed eye type
 
    CC
 
 (MP3)
 
 Table 27
 
 Rod-end integral trunnion type
 TA
 (MT l)
 Table 28
 Trunnion
 Head·end integral trunnion type
    TB
(MT 2)
Table 28
 types
 
 
 Intermediate fixed trunnion type
 
    TC
 
 (MT4)
 
 Tables 29&30

7
E 8354.1992
Remarks l.Those of which mounting methods are inevitably particular ones shall be
    designated as X-shape,such as LX,FX and the like.
2.
The fixed eye form in the crevice types shall mean an integrated construc-
tion in which an eye fitting is welded with the head,and the deb tchable
eye form and detachable crevice form shall mean those construct ion in
which eyes and crevice fittings have been assembled with bodies by tie
rods.
3.The symbols given in()are shown for informative reference,al.d are in
    accordance with JIS B 8366.
(3) Materials of packing and gasket
    as given in Table 5 according to
 Packings and gaskets shall be(1assified
materials.
Table 5.Materials of packing and gasket

 Material of packing and gasket
 Symbol
 Nitrile rubber
    l
 Urethane rubber
    2
 Fluorine。contained rubber
    3
 Ethylene tetrafluoride resin
    4
 Metal    .
    5
 Others
    6

 

本文链接: http://www.yzgj.cn/yzgjcn_172.html
如需转载请注明:扬子工具液压千斤顶http://www.yzgj.cn

本文章总10页 1 2 3 4 5 6 7 8 9 10 下一页

上一篇:伸缩式套筒液压缸
下一编:液压接头和插头尺寸规范
千斤顶相关知识
液压千斤顶高压胶管、高压硬管外径参考
润滑油基础知识
液压缸工作时产生牵引力不足或速度下降现象的原因及排除方法
液体动力学
液压油的污染及其控制
设计液压缸要考虑的问题
液压千斤顶相关产品(请点击产品名称查看详细资料)
电动液压千斤顶(海力F-V50-1000T) - 同步千斤顶 - 大吨位液压顶(海力F-Q顶管机大行程) 大吨位分离式液
压顶
薄型顶(吨位5-200T行程6-80mm) - 薄型同步千斤顶(薄型海力B-V)
桥梁千斤顶(海力M-B) - 超薄型千斤顶(RSM5-150T) - 薄型千斤顶(RCS5-100T)
空间窄小-如桥梁
更换支座
穿心千斤顶(海力H-C空心顶) - 空心千斤顶(RCH穿心顶) - 双作用空心千斤顶(RRH) 具有拉伸功能空
心液压顶
自锁千斤顶(海力L-V50-1080T) - 自锁同步千斤顶 - 自锁式千斤顶(CLL) 需长时间支撑重
物液压顶
分离式千斤顶(10-200T) - 手动千斤顶(5-100T) - 双节千斤顶(多节) 小吨位分离式液
压顶
超高压千斤顶(CLR) - 电动千斤顶(DYG) - 大吨位千斤顶(CLS) 大吨位液压顶旧
型号
电动泵(海力B-V电动泵站) - 手动泵(YSB单向) - 双向手动泵(YSSB) - 单向手动泵(YCSB)
液压千斤顶选型调查表(在括号中填上数据,并留下联系方法,最后再提交)
单位:
姓名:
电话:
传真:
手机:
邮箱: